AST Weld-in Roll Cage BMW E30 Sedan V5

€1.265,95 Incl. VAT

AST Weld-in Roll Cage BMW E30 Sedan V5

This full roll cage is the most comprehensive specification in the weld-in range for the rear-wheel-drive BMW E30 saloon: the complete set of bars, with door bars, front bars to the bulkhead, diagonals and harness bar. Eight welded mounting points, E355 steel, supplied as an unpainted weld-in kit with gussets and fitting instructions. Delivery time 15 to 35 working days.

Available on back-order|Estimated delivery time: 15 tot 35 werkdagen

SKU: CMBN00277 Category: Brand:

Description

AST Weld-in Roll Cage BMW E30 Sedan V5

The AST Weld-in Roll Cage BMW E30 Sedan V5 is a full roll cage for the BMW E30 with 4-door saloon bodywork, built for the rear-wheel-drive E30. This Weld-in E30 Sedan V5 is the complete set of bars and therefore the most comprehensive specification in the entire weld-in range.

The cage is designed and built by AST Roll Cages in Spain, for drivers who are building up their E30 as a fully-fledged competition car and do not want to have to add anything further.

Key benefits

  • Complete set of bars everything from the V4 plus the remaining reinforcement; there is nothing left to add to this structure.
  • Maximum torsional rigidity the bodyshell works as a single unit, which keeps the suspension set-up precise.
  • Full side protection door bars on both sides, supported by the sill reinforcements.
  • Harness bar a correctly positioned mounting point for the shoulder straps.
  • Eight welded mounting points permanently anchored, with gussets at all load points.
  • E355 structural steel: main hoop with a diameter of 45 mm, other tubes with a diameter of 40 mm.
  • Complete weld-in kit 3 mm reinforcement plates, mounting hardware, documentation and sticker set included.

Suitable for

BMW E30 3 Series, 4-door saloon, rear-wheel drive

  • BMW E30 3 Series 4-door Saloon
  • Exclusively for the rear-wheel-drive E30; the all-wheel-drive 325iX requires a separate AWD version
  • Type: weld-in roll cage, version V5
  • Drifting, track use and rallying

Technical specifications

  • Manufacturer: AST Roll Cages
  • Manufacturer part number: CMBN00277
  • Sunroof: for roofs without a sunroof
  • Headlining: for roofs without headlining
  • Rear anchorage: in the rear suspension area
  • Rear structure layout: X design
  • Type: full roll cage, weld-in (permanent)
  • Main hoop: E355 steel, 45 mm diameter
  • Secondary structure: E355 steel, 40 mm diameter
  • Foot plates: 3 mm steel, custom-designed for each car
  • Mounting: 8 welded mounting points on the bodyshell
  • Weight: 71 kg (manufacturer’s figure)
  • Finish: unpainted weld-in kit
  • Included: weld-in kit, gussets, reinforcement plates, bolts, washers and nuts, documentation, fitting instructions and sticker set

Fitting and delivery

The cage is built to order; the standard delivery time is 15 to 35 working days. At this specification level, the interior is stripped almost completely bare before welding begins; allow for several days of stripping and welding by an experienced cage builder.

The V5 is the final step in the weld-in range: the full set of bars, permanently welded into the rear-wheel-drive E30 saloon.

Why choose this Weld-in E30 Saloon V5 roll cage?

If you are stripping a car right down to weld in a cage anyway, it is a waste to have to weld in extra bars afterwards. The V5 gives you the maximum straight away. AST digitises the bodyshell with laser scanners and designs the cage in 3D, so that even with this number of tubes everything connects in the right place and hardly any fitting and grinding work remains.

Frequently asked questions

Why should I choose the V5 rather than the V4?

The Weld-in E30 Sedan V5 has the full set of bars, making it the most rigid and best-protected level. If you compete in a class with strict requirements, or you do not want to have to change anything later, this is the logical choice.

Does this cage fit a 325iX?

No. This version is designed for the rear-wheel-drive E30 saloon. The all-wheel-drive 325iX requires the separate AWD version because of its different floor and transmission tunnel.

What is the delivery time?

The standard delivery time for this roll cage is 15 to 35 working days.

Delivery outside the European Union: different shipping costs may apply. Don’t worry: we will email you as soon as possible after your order and agree the shipping with you. You are not committed to anything without your consent.

Additional information

Weight71 kg
Car make

BMW

Model

E30

Reviews

There are no reviews yet.

Be the first to review “AST Weld-in Roll Cage BMW E30 Sedan V5”
EN

Your Shopping cart

Close