AST Multipoint Weld-in Roll Cage Nissan 280Z S30 Coupé V4

€1.364,54 Incl. VAT

AST Multipoint Weld-in Roll Cage Nissan 280Z S30 Coupé V4

This full roll cage from AST Roll Cages combines door bars, front reinforcement and an extra diagonal brace and harness bar on ten welded mounting points in the Nissan 280Z S30 Coupé. Built to FIA Appendix J, custom-made using laser scanning, unpainted 71 kg weld-in kit. Delivery time 15 to 35 working days.

Available on back-order|Estimated delivery time: 15 tot 35 werkdagen

Choose the layout of the structure at the rear of the roll cage.

SKU: CMBN01776 Category: Brand:

Description

AST Multipoint Weld-in Roll Cage Nissan 280Z S30 Coupé V4

The Multipoint 280Z Coupé V4 is a full roll cage for the Nissan 280Z with the S30 chassis and 3-door Coupé bodywork, permanently welded in at ten points. To the door bars and front reinforcement of the V3, this version adds an extra diagonal brace and a harness bar.

This means the structure covers the three load directions that matter in practice: torsion, side impact and harness loads in a frontal crash. Built to FIA Appendix J.

Key benefits

  • Harness bar for mounting the shoulder straps at the prescribed height.
  • Extra diagonal brace in the main hoop to resist torsion.
  • Door bars and front reinforcement bars from the lower versions.
  • Ten welded mounting points for the widest load distribution in the range.
  • Built to FIA Appendix J, with homologation numbers stated by the manufacturer.
  • 71 kg according to the manufacturer’s figure.
  • Fully custom-made via laser scan and 3D design.
  • Available with an X design or V design rear structure, which you choose when ordering

Suitable for

Nissan 280Z, S30 chassis, 3-door coupé

  • Nissan 280Z S30 Coupé
  • Type: full roll cage, multipoint welded-in, version V4
  • Circuit racing, drifting and historic rallying

Technical specifications

  • Manufacturer: AST Roll Cages
  • Manufacturer part number: CMBN01776
  • Sunroof: for roofs without a sunroof
  • Headlining: for roofs without headlining
  • Rear anchorage: in the rear suspension area
  • Type: full roll cage with door bars, diagonal brace and harness bar, permanently welded in at ten points
  • Main hoop: E355 steel, 45 mm diameter
  • Secondary structure: E355 steel, 40 mm diameter
  • Reinforcement plates: 3 mm steel, custom-designed for each car
  • Mounting: 10 welded mounting points on the bodyshell
  • Homologation: FIA homologation number 3022 / 3023 / 3084, as stated by AST Roll Cages
  • Valid for the versions Nissan Datsun Sports Z S30, Nissan Datsun Sports 240Z H(L)S30, Nissan Datsun 280Z and Nissan Datsun 260Z 2+2
  • Weight: 210 kg (manufacturer’s figure)
  • Finish: weld-in kit, unpainted
  • Included: weld-in kit, gussets, reinforcement plates, bolts, washers and nuts, documentation, fitting instructions and sticker set

Fitting and delivery

Allow 15 to 35 working days for delivery and expect a complete interior strip-out. The cage is welded to the bare bodyshell at ten points, and the tube count is higher than on the lower versions. This is not a weekend job: book workshop time with a fabricator who has welded in cages before.

Torsion, side impact and harness loads: this version has a tube for every scenario.

Why choose this Multipoint 280Z Coupé V4?

Anyone building an S30 to this level no longer drives it to the circuit but trailers it there. The harness bar is where the regulations and real-world practice meet: without a correct harness mount, the rest of the cage is worth far less. Combined with ten welded mounting points, you get a structure that spares the old bodywork yet gives nothing away.

Frequently asked questions

Which FIA homologation does this cage have?

AST Roll Cages lists homologation number 3022 / 3023 / 3084 for the Multipoint 280Z Coupé V4, which according to the manufacturer is valid for the Nissan Datsun Sports Z S30, Nissan Datsun Sports 240Z H(L)S30, Nissan Datsun 280Z and Nissan Datsun 260Z 2+2.

What is the harness bar for?

This bar is where you attach the shoulder straps of your harness, at the height specified by the harness manufacturer, so that the harness restrains the torso instead of loading the spine.

Can I extend the cage later?

With a welded-in structure, extending it means cutting and welding again. So choose the level you want up front.

Can I choose between X design and V design?

Yes. When ordering, state which shape you want for the rear structure, and AST will build the roll cage in that version. The price is the same for both shapes.

What is the delivery time?

The standard delivery time for this roll cage is 15 to 35 working days.

Delivery outside the European Union: different shipping costs may apply. Don’t worry: we will email you as soon as possible after your order and agree the shipping with you. You are not committed to anything without your consent.

Additional information

Weight210 kg
Car make

Nissan

Model

280Z, S30

Reviews

There are no reviews yet.

Be the first to review “AST Multipoint Weld-in Roll Cage Nissan 280Z S30 Coupé V4”
EN

Your Shopping cart

Close