Description
The MTS Street Polo 86 Inox is a height-adjustable send-in kit (coilover) from MTS Technik for the Volkswagen Polo 86/86C / Derby, model years 1975 to 1994. Street is the standard setup from MTS Technik: a good balance between comfort and firmness.
On the Inox version, the damper bodies are made of stainless steel, so road salt and moisture don’t stand a chance. This is a send-in kit: MTS Technik builds the kit with your own original front struts, so you don’t have to weld anything yourself.
Key benefits of the MTS Street Polo 86 Inox
- Stainless steel damper bodies, resistant to road salt and moisture
- Lower by 35 to 85 mm, front and rear independently adjustable
- Eibach springs, matched to this set
- Gas-oil twin-tube dampers that stay stable even under intensive use
- hexaCOIL spring perch: the adjusting nut does not seize up during adjustment
- 2 year warranty with no mileage limit
Suitable for
The MTS Street Polo 86 Inox fits the following versions:
- Volkswagen Polo 86 (type 86, 03/1975 to 09/1981): 0.9, 1.1, 1.3
- Volkswagen Polo 86C (also Coupe and Classic, type 86C/80, 10/1981 to 09/1994): 0.9, 1.0, 1.0 Cat, 1.1, 1.3, 1.3 Cat, 1.3 D, 1.4 D, 1.3 G40
- Volkswagen Derby (type 86/86C/80, 02/1977 to 12/1984): 0.9, 1.1, 1.3, 1.0
Note: only for cars without level control (NIVO) or factory air suspension. Axle load: maximum 640 kg front and maximum 630 kg rear; check your car’s vehicle type plate.
Technical specifications of the MTS Street Polo 86 Inox
- Product: MTS Street Polo 86 Inox
- Manufacturer: MTS Technik
- Article number: XMTSGWVW83
- EAN: 5903855657120
- Version: Street, Inox (stainless steel)
- Type of kit: send-in kit, made using your own original front struts
- Lowering: front 35 to 85 mm, rear 35 to 75 mm
- Height adjustment: front and rear via threaded damper body
- Camber plates: not included
- Included: complete front and rear set with springs and height adjustment
- TÜV certificate: no
- Weight: 24.9 kg
- Warranty: 2 years with no mileage limit
Fitting and delivery
MTS Technik builds the MTS Street Polo 86 Inox with your own original front struts: after receipt they are stripped of their paint, welded to size and zinc-plated.
- The stated lowering applies relative to the standard suspension. If the car has a factory sport suspension, the lowering will be smaller.
- When fitting, check the clearance between tyre or wheel and the strut: at least 5 mm. If it is less, use approved wheel spacers.
- After fitting the MTS Street Polo 86 Inox, have the wheel alignment checked, because camber and toe change as well.
How a send-in kit works
- After your order we will email you the shipping instructions and the address for your original front struts.
- Beforehand, remove all parts from the struts, such as hubs, bearings, cover caps, damper cartridges, bolts and nuts. If the struts arrive not disassembled, or if damage is found (for example broken bolts), they will be sent back or extra costs will be charged.
- Send in the struts in their original paint, even if it looks bad. Do not spray or paint them beforehand; they are stripped, welded and then zinc-plated.
- Because the kit is made to measure with your struts, the right of withdrawal for distance purchases does not apply: a send-in kit cannot be returned.
- This kit is only delivered within the European Union.
The delivery time depends on when your struts arrive. After your order we will keep you updated by email about the dispatch and the expected delivery time.
The MTS Street Polo 86 Inox combines stainless steel damper bodies and up to 85 mm of lowering for the Volkswagen Polo 86/86C / Derby.
Why choose the MTS Street Polo 86 Inox?
With the MTS Street Polo 86 Inox you choose the setup MTS Technik itself recommends as standard: enough lowering for a tight stance, and a character that doesn’t become tiring on the road. If you also drive in winter or the car is parked outside, the Inox version pays for itself: stainless steel doesn’t rust, so the thread of the height adjustment doesn’t seize up. If you mainly drive in summer, the Gold version is a more affordable alternative. And because it is a send-in kit, you don’t have to weld anything yourself.
Frequently asked questions
What is the difference between Gold and Inox?
Gold has steel damper bodies with a yellow zinc coating, Inox has stainless steel damper bodies. Inox is more resistant to road salt and moisture and therefore costs more. Otherwise, the kits are identical.
Can I return a send-in kit?
No. Because the kit is made to measure with your own struts, the right of withdrawal for distance purchases does not apply.
How long does delivery take?
The delivery time of the MTS Street Polo 86 Inox depends on when your struts arrive. After your order we will keep you updated by email about the dispatch and the expected delivery time.
Other MTS Technik sets for the Polo 86
Delivery outside the European Union: different shipping costs may apply. Don’t worry: we will email you as soon as possible after your order and agree the shipping with you. You are not committed to anything without your consent.
EN
NL
FR
DE
Reviews
There are no reviews yet.