Shop

The MTS Street A8 D2 Inox is a height-adjustable coilover kit from MTS Technik for the Audi A8 D2, model years 1994 to 2005. Street is the standard setup from MTS Technik: a good balance between comfort and firmness, for daily use and the occasional track day or drift day.

On the Inox version, the damper bodies are made of stainless steel, so road salt and moisture don’t stand a chance.

Key benefits

• Stainless steel damper bodies, resistant to road salt and moisture
• Lower by 10 to 60 mm, front and rear independently adjustable
• Eibach springs of 150 N/mm front and 82.2 N/mm rear
• Gas-oil twin-tube dampers that stay stable even under intensive use
• hexaCOIL spring perch: the adjusting nut does not seize up during adjustment
• TÜV certificate and 2 year warranty with no mileage limit

Suitable for

The MTS Street A8 D2 Inox fits the following versions:

• Audi A8 D2 (type 4D2/4D8, 03/1994 to 12/2005): 2.5 TDI, 2.8, 3.7, 2.5 TDI quattro, 2.8 quattro, 3.3 TDI quattro, 3.7 quattro, 4.2 quattro, S8 quattro

Note for the MTS Street A8 D2 Inox: axle load: maximum 1380 kg front and maximum 1230 kg rear; check your car’s vehicle type plate.

Fitting is also possible on cars with level control (NIVO) or factory air suspension; the air suspension system must then be removed first. Sometimes extra original parts are needed for this.

Technical specifications

• Product: MTS Street A8 D2 Inox
• Manufacturer: MTS Technik
• Article number: XMTSGWAU22
• EAN: 5903855630475
• Version: Street, Inox (stainless steel)
• Lowering: front 10 to 60 mm, rear 10 to 30 mm
• Springs (Eibach): GWFE24VA with 150 N/mm front, GWFE23HA with 82.2 N/mm rear
• Helper springs: GWHE02 (20 N/mm)
• Height adjustment: front via threaded damper body, rear via separate adjuster element
• Thread block rear: at the bottom
• Camber plates: not included
• Included: complete front and rear set with springs and height adjustment
• TÜV certificate: yes
• Weight: 24.9 kg
• Warranty: 2 years with no mileage limit

Fitting and delivery

The MTS Street A8 D2 Inox replaces the original dampers and springs and fits on the original mounting points.

• The stated lowering applies relative to the standard suspension. If the car has a factory sport suspension, the lowering will be smaller.
• When fitting, check the clearance between tyre or wheel and the strut: at least 5 mm. If it is less, use approved wheel spacers.
• Tip for adjusting the rear: remove the height adjuster, set the spring seat to the new position and refit the adjuster.
• After lowering, have the wheel alignment checked, because camber and toe change as well.

Delivery: 4 to 7 working days while manufacturer stock lasts.

The MTS Street A8 D2 Inox combines stainless steel damper bodies, Eibach springs of 150 and 82.2 N/mm and up to 60 mm of lowering for the Audi A8 D2.

Why choose the MTS Street A8 D2 Inox?

With the MTS Street A8 D2 Inox you choose the setup MTS Technik itself recommends as standard: enough lowering for a tight stance, and a character that doesn’t become tiring on the road. If you also drive in winter or the car is parked outside, the Inox version pays for itself: stainless steel doesn’t rust, so the thread of the height adjustment doesn’t seize up. If you mainly drive in summer, the Gold version is a more affordable alternative.

Frequently asked questions

What is the difference between Street and Stance?

All versions use the same dampers; the difference lies in the Eibach springs and the lowering range: Street (150 and 82.2 N/mm) and Stance (200 and 82.2 N/mm). Street is the standard. Stance is the firmest and the lowest.

What is the difference between Gold and Inox?

Gold has steel damper bodies with a yellow zinc coating, Inox has stainless steel damper bodies. Inox is more resistant to road salt and moisture and therefore costs more. Otherwise, the kits are identical.

How long does delivery take?

The MTS Street A8 D2 Inox is delivered within 4 to 7 working days as long as the manufacturer has stock.