Shop

The MTS Street F01 Inox is a height-adjustable coilover kit from MTS Technik for the BMW 5-series (F10), 6-series (F06) and 7-series (F01, F02, F03 and F04), model years 2008 to 2018. Street is the standard setup from MTS Technik: a good balance between comfort and firmness, for daily use and the occasional track day or drift day.

On the Inox version, the damper bodies are made of stainless steel, so road salt and moisture don’t stand a chance.

Key benefits

• Stainless steel damper bodies, resistant to road salt and moisture
• Lower by 30 to 65 mm, front and rear independently adjustable
• Eibach springs of 84 N/mm front and 23 to 36 N/mm rear
• Gas-oil twin-tube dampers that stay stable even under intensive use
• hexaCOIL spring perch: the adjusting nut does not seize up during adjustment
• TÜV certificate and 2 year warranty with no mileage limit

Suitable for

The MTS Street F01 Inox fits the following versions:

• 5 Series F10 Sedan (01/2009 to 10/2016): 518d, 520d, 520i, 523i, 525d, 528i, 530d, 530i, 535d, 535i, 550i
• 6 Series F06 Gran Coupe (03/2012 to 10/2018): 640d, 640i, 650i
• 7 Series F01/F02/F03/F04 Sedan (02/2008 to 12/2015): 730d, 730i, Li, 740d, 740i, Li, 750i, 750i, Li, ActiveHybrid 7

Note: not suitable for versions with four-wheel drive (xDrive). Only for cars without level control (NIVO) or factory air suspension. Axle load: maximum 1280 kg front and maximum 1435 kg rear; check your car’s vehicle type plate.

Fitting is also possible on cars with electronically adjustable damping; that system must then be disabled.

Technical specifications

• Product: MTS Street F01 Inox
• Manufacturer: MTS Technik
• Article number: XMTSGWBM44
• EAN: 5903855655638
• Version: Street, Inox (stainless steel)
• Lowering: front 30 to 65 mm, rear 30 to 60 mm (depending on the model)
• Springs (Eibach): GWFE255VA with 84 N/mm front, GWFE78HA with 23 to 36 N/mm rear
• Helper springs: GWHE01 (20 N/mm)
• Height adjustment: front and rear via threaded damper body
• Camber plates: not included
• Included: complete front and rear set with springs and height adjustment
• TÜV certificate: yes
• Weight: 24.9 kg
• Warranty: 2 years with no mileage limit

Fitting and delivery

The MTS Street F01 Inox replaces the original dampers and springs and fits on the original mounting points.

• The stated lowering applies relative to the standard suspension. If the car has a factory sport suspension, the lowering will be smaller.
• When fitting, check the clearance between tyre or wheel and the strut: at least 5 mm. If it is less, use approved wheel spacers.
• After lowering, have the wheel alignment checked, because camber and toe change as well.

Delivery: 4 to 7 working days while manufacturer stock lasts.

The MTS Street F01 Inox combines stainless steel damper bodies, Eibach springs of 84 and 23-36 N/mm and up to 65 mm of lowering for the BMW 5 Series (F10), 6 Series (F06) and 7 Series (F01, F02, F03 and F04).

Why choose the MTS Street F01 Inox?

With the MTS Street F01 Inox you choose the setup MTS Technik itself recommends as standard: enough lowering for a tight stance, and a character that doesn’t become tiring on the road. If you also drive in winter or the car is parked outside, the Inox version pays for itself: stainless steel doesn’t rust, so the thread of the height adjustment doesn’t seize up. If you mainly drive in summer, the Gold version is a more affordable alternative.

Frequently asked questions

Does this kit also fit a four-wheel-drive (xDrive) version?

No. The MTS Street F01 Inox is made for the rear-wheel-drive versions.

What is the difference between Gold and Inox?

Gold has steel damper bodies with a yellow zinc coating, Inox has stainless steel damper bodies. Inox is more resistant to road salt and moisture and therefore costs more. Otherwise, the kits are identical.

How long does delivery take?

The MTS Street F01 Inox is delivered within 4 to 7 working days as long as the manufacturer has stock.