Shop

The MTS Street Mustang 6 Inox is a height-adjustable coilover kit from MTS Technik for the Ford Mustang 6, from model year 2014. Street is the standard setup from MTS Technik: a good balance between comfort and firmness, for daily use and the occasional track day or drift day.

On the Inox version, the damper bodies are made of stainless steel, so road salt and moisture don’t stand a chance.

Key benefits

• Stainless steel damper bodies, resistant to road salt and moisture
• Lower by 20 to 65 mm, front and rear independently adjustable
• Eibach springs of 55 N/mm front and 145 N/mm rear
• Gas-oil twin-tube dampers that stay stable even under intensive use
• hexaCOIL spring perch: the adjusting nut does not seize up during adjustment
• 2 year warranty with no mileage limit

Suitable for

The MTS Street Mustang 6 Inox fits the following versions:

• Ford Mustang 6 Coupe and Cabrio (from 02/2014): 2.3 EcoBoost, 3.7 V6, 5.0 V8, 5.0 V8 Bullitt, 5.2 Shelby GT350, 5.2 Shelby GT500, EcoBoost, V8 GT

Note: only for cars without electronically controlled damping. Axle load: maximum 1100 kg front and maximum 1150 kg rear; check your car’s vehicle type plate.

Fitting is also possible on cars with electronically adjustable damping; that system must then be disabled.

Technical specifications

• Product: MTS Street Mustang 6 Inox
• Manufacturer: MTS Technik
• Article number: XMTSGWFO24
• EAN: 5903855655799
• Version: Street, Inox (stainless steel)
• Lowering: front 20 to 65 mm, rear 20 to 70 mm
• Springs (Eibach): GWFE259VA with 55 N/mm front, GWFE260HA with 145 N/mm rear
• Height adjustment: front via threaded damper body, rear via separate adjuster element
• Thread block rear: at the top
• Camber plates: not included
• Included: complete front and rear set with springs and height adjustment
• TÜV certificate: no
• Weight: 24.9 kg
• Warranty: 2 years with no mileage limit

Fitting and delivery

The MTS Street Mustang 6 Inox replaces the original dampers and springs and fits on the original mounting points.

• The stated lowering applies relative to the standard suspension. If the car has a factory sport suspension, the lowering will be smaller.
• When fitting, check the clearance between tyre or wheel and the strut: at least 5 mm. If it is less, use approved wheel spacers.
• After lowering, have the wheel alignment checked, because camber and toe change as well.

Delivery: 4 to 7 working days while manufacturer stock lasts.

The MTS Street Mustang 6 Inox combines stainless steel damper bodies, Eibach springs of 55 and 145 N/mm and up to 65 mm of lowering for the Ford Mustang 6.

Why choose the MTS Street Mustang 6 Inox?

With the MTS Street Mustang 6 Inox you choose the setup MTS Technik itself recommends as standard: enough lowering for a tight stance, and a character that doesn’t become tiring on the road. If you also drive in winter or the car is parked outside, the Inox version pays for itself: stainless steel doesn’t rust, so the thread of the height adjustment doesn’t seize up. If you mainly drive in summer, the Gold version is a more affordable alternative.

Frequently asked questions

What is the difference between Gold and Inox?

Gold has steel damper bodies with a yellow zinc coating, Inox has stainless steel damper bodies. Inox is more resistant to road salt and moisture and therefore costs more. Otherwise, the kits are identical.

How long does delivery take?

The MTS Street Mustang 6 Inox is delivered within 4 to 7 working days as long as the manufacturer has stock.

Other MTS Technik sets for the Mustang 6

• Ford Mustang 6 (14-) MTS Technik coilover kit (front camber plates)