Description
Hydraulic Handbrake Hose 165cm, Steel Braided Teflon Brake Line, 3/8 UNF to M10x1
This hydraulic handbrake hose connects the cylinder of a hydraulic handbrake to the brake system of your drift or race car. The hose is 165 cm long, crimped and made as a PTFE (Teflon) line with steel braiding. At the cylinder end there is a 3/8 UNF banjo connection, at the other end an M10x1 fitting.
The hose is intended for a hydraulic handbrake with an OBP cylinder with reservoir. With the M10x1 connection you can easily connect it to a commonly available brake T-piece.
Contents
Key benefits of this hydraulic handbrake hose
- PTFE hose with steel braiding: does not expand under pressure like a rubber hose
- Crimped ends, ready to fit
- Stainless steel end fittings that do not rust
- 165 cm long, enough for a neat route through the car
- 3/8 UNF banjo for the OBP cylinder with reservoir
- M10x1 fitting for a standard brake T-piece
- Black carbon-look outer sheath
Suitable for
Hydraulic handbrakes with OBP cylinder with reservoir
- Hydraulic handbrake with OBP cylinder and reservoir (3/8 UNF outlet)
- Connection to a brake T-piece with M10x1 inlet
- Drift, rally and circuit cars with a hydraulic handbrake in the interior
Technical specifications
- Item number: 0291
- Type: hydraulic handbrake hose, crimped and steel-braided
- Hose material: PTFE (Teflon) with steel braiding
- Outside: black, carbon-look
- End fittings: stainless steel
- Length: 165 cm
- Connection, cylinder end: 3/8 UNF (banjo)
- Connection, other end: M10x1
- Contents: 1 hose, 1 banjo end fitting 3/8 UNF, 1 end fitting M10x1
Installation and delivery
Connect the banjo end to the outlet of the handbrake cylinder and route the hose to where the T-piece sits. There you connect it to the brake system with the M10x1 fitting. Make sure the hose does not run along sharp edges or hot parts anywhere and secure it along the way with clips or cable ties.
Use new copper washers at the banjo, tighten the fittings to the correct torque and then bleed the system thoroughly. During a first test, check that all connections stay dry before you go on track.
You will find all cylinders and parts for the drift handbrake in our hydraulic handbrakes category. A matching cylinder is the OBP drift handbrake with reservoir.
A handbrake is only as good as its line: a firm hose gives direct feel in the lever.
Plan the route of the hydraulic handbrake hose before you start fitting. Measure the distance from the handbrake cylinder to the T-piece and check whether a pass-through in the floor or tunnel is needed. Always use a rubber grommet on such a pass-through, so that the braiding does not chafe against the edge of the panel. A hose that is pulled too tight or has a sharp kink will not last as long, so leave some slack at the connections.
Why choose this hydraulic handbrake hose?
A rubber brake hose expands slightly under high pressure, and you notice that as a spongy lever. A braided PTFE hose keeps its shape, so the force of your hand goes straight to the brake calipers. And with the right connections already fitted, you are finished quickly.
Frequently asked questions
How long is the hose?
The hydraulic handbrake hose is 165 cm long.
Which connections does it have?
A 3/8 UNF banjo for the cylinder and an M10x1 fitting for the brake T-piece.
Which handbrake does the hose fit?
A hydraulic handbrake with an OBP cylinder with reservoir, which has a 3/8 UNF outlet.
Is a T-piece included?
No, the set consists of the hose with the two end fittings. You buy the T-piece separately.
Why a braided hose?
The steel braiding prevents the hose from expanding under pressure. This makes the handbrake feel firmer and respond more directly.
Delivery outside the European Union: different shipping costs may apply. Don’t worry: we will email you as soon as possible after your order and agree the shipping with you. You are not committed to anything without your consent.








Reviews
There are no reviews yet.