Shop

The MTS Street Passat B6 Inox is a height-adjustable coilover kit from MTS Technik for the Volkswagen Passat B6/B7 / CC B7 / Passat CC B6 and Skoda Superb 2 / Yeti, model years 2005 to 2017. Street is the standard setup from MTS Technik: a good balance between comfort and firmness, for daily use and the occasional track day or drift day.

On the Inox version, the damper bodies are made of stainless steel, so road salt and moisture don’t stand a chance.

Key benefits of the MTS Street Passat B6 Inox

• Stainless steel damper bodies, resistant to road salt and moisture
• Lower by 35 to 70 mm, front and rear independently adjustable
• Eibach springs of 54 N/mm front
• Gas-oil twin-tube dampers that stay stable even under intensive use
• hexaCOIL spring perch: the adjusting nut does not seize up during adjustment
• TÜV certificate and 2 year warranty with no mileage limit

Suitable for

The MTS Street Passat B6 Inox fits the following versions:

• Volkswagen Passat B6 (also Variant, type 3C2/3C5, 03/2005 to 12/2013): 1.4 TSI, 1.6, 1.6 FSI, 1.6 TDI, 1.8 TSI, 1.9 TDI, 2.0 BlueTDI, 2.0 FSI, 2.0 TDI, 2.0 TDI 16V, 2.0 TFSI, 2.0 FSI 4motion, 2.0 TDI 16V 4motion, 2.0 TDI 4motion, 3.2 FSI 4motion, 3.6 R36 4motion, 3.6 FSI
• Volkswagen Passat B7 (also Variant, type 362/365, 08/2010 to 04/2016): 1.4 TSI, 1.6 TDI, 1.8 TSI, 2.0 TDI, 2.0 TSI, 2.0 TDI 4motion, 3.6 FSI 4motion
• Volkswagen CC B7 (type 358, 11/2011 to 10/2017): 1.4 TSI, 1.4 TSI MultiFuel, 1.8 TSI, 2.0 TFSI, 2.0 TSI, 3.6 FSI, 2.0 TDI 4motion
• Volkswagen Passat CC B6 (type 357, 02/2008 to 12/2013): 1.8 TSI, 2.0 TDI, 2.0 TFSI, 2.0 TSI, 2.0 TDI 4motion, 3.6 FSI 4motion
• Skoda Superb 2 (also Estate, type 3T4/3T5, 03/2008 to 05/2015): 1.4 TSI, 1.6 TDI, 1.8 TSI, 1.9 TDI, 2.0 TDI, 2.0 TDI 16V, 2.0 TFSI, 1.8 TSI 4×4, 2.0 TDI 16V 4×4, 2.0 TDI 4×4, 3.6 FSI 4×4, 3.6 V6 4×4
• Skoda Yeti (type 5L, 05/2009 to 12/2017): 1.2 TSI, 1.4 TSI, 1.6, 2.0 TDI, 1.4 TSI 4×4, 1.8 TSI 4×4, 2.0 TDI 4×4

Note for the MTS Street Passat B6 Inox: axle load: 1100 to 1200 kg front and maximum 1250 kg rear; check your car’s vehicle type plate.

If the car has Audi Magnetic Ride (AMR), that system must be disabled. A suitable module for this is only available on request.

Technical specifications

• Product: MTS Street Passat B6 Inox
• Manufacturer: MTS Technik
• Article number: XMTSGWVW45
• EAN: 5903855625280
• Version: Street, Inox (stainless steel)
• Lowering: front 35 to 70 mm, rear 35 to 60 mm
• Springs (Eibach): GWFE40HA with 54 N/mm front
• Height adjustment: front via threaded damper body, rear via separate adjuster element
• Thread block rear: at the top
• Camber plates: not included
• Included: complete front and rear set with springs and height adjustment
• TÜV certificate: yes
• Weight: 24.9 kg
• Warranty: 2 years with no mileage limit

Fitting and delivery

The MTS Street Passat B6 Inox replaces the original dampers and springs and fits on the original mounting points.

• The stated lowering applies relative to the standard suspension. If the car has a factory sport suspension, the lowering will be smaller.
• When fitting, check the clearance between tyre or wheel and the strut: at least 5 mm. If it is less, use approved wheel spacers.
• Sometimes the rear height adjuster has to be removed to achieve the maximum lowering.
• Tip for adjusting the rear: remove the height adjuster, set the spring seat to the new position and refit the adjuster.
• After fitting the MTS Street Passat B6 Inox, have the wheel alignment checked, because camber and toe change as well.

Delivery: 4 to 7 working days while manufacturer stock lasts.

The MTS Street Passat B6 Inox combines stainless steel damper bodies, Eibach springs of 54 N/mm and up to 70 mm of lowering for the Volkswagen Passat B6/B7 / CC B7 / Passat CC B6 and Skoda Superb 2 / Yeti.

Why choose the MTS Street Passat B6 Inox?

With the MTS Street Passat B6 Inox you choose the setup MTS Technik itself recommends as standard: enough lowering for a tight stance, and a character that doesn’t become tiring on the road. If you also drive in winter or the car is parked outside, the Inox version pays for itself: stainless steel doesn’t rust, so the thread of the height adjustment doesn’t seize up. If you mainly drive in summer, the Gold version is a more affordable alternative.

Frequently asked questions

What is the difference between Gold and Inox?

Gold has steel damper bodies with a yellow zinc coating, Inox has stainless steel damper bodies. Inox is more resistant to road salt and moisture and therefore costs more. Otherwise, the kits are identical.

How long does delivery take?

The MTS Street Passat B6 Inox is delivered within 4 to 7 working days as long as the manufacturer has stock.

Other MTS Technik sets for the Passat B6

• Volkswagen Passat B6/B7 / CC B7, Seat Altea (04-17) MTS Technik coilover kit (front camber plates)